Home - News - Details

Common Faults And Solutions Of Band Saws

Common faults and solutions of band saws

Should I change the sawing machine? What kind of sawing machine should I choose?

When we choose to invest in a sawing machine, we often face a dilemma: should we buy a high-priced sawing machine with good performance, or a low-priced economical sawing machine? How to measure the cost-effectiveness of a sawing machine? The sawing machine is old, should I change it? Is it worth changing?

 

1. Evaluation method for purchasing a new sawing machine
In engineering economics, an incremental investment rate of return method is often used to quantitatively evaluate the two options of large one-time investment but small annual production cost and small one-time investment but high annual production cost. If the calculated incremental investment rate of return is greater than the benchmark investment rate of return set by the company (the most superficial explanation of the benchmark investment rate of return is the minimum expected value of annual income with one million in hand), then this large investment plan is feasible, otherwise it is not feasible (under the same total production income).
The formula for this rate of return is:


R(2-1): incremental investment rate of return
Scheme 2: A plan with large investment, low production cost and advanced technology.
Scheme 1: A plan with small investment, high production cost and less advanced technology than the former.
C1: Annual production cost (operating cost) of Option 1
C2: Annual production cost (operating cost) of Option 2
I1: Total investment of Option 1
I2: Total investment of Option 2

The following costs (C) are usually considered in the sawing production cost:
Losses caused by bad cutting
Labor efficiency
Equipment depreciation and maintenance costs
Annual saw blade usage cost
Take the sawing selection option of high-speed aluminum ingot cutting as an example:
Option 1: Equipment investment is RMB 800,000.
Option 2: Equipment investment is RMB 1.3 million.
The company's investment benchmark rate of return is 13%.
Assumption 1: Bad cutting of materials will not cause large cost losses, labor efficiency is the same, one person operates a sawing machine, but saw blade loss accounts for a large proportion of the cost. The sawing machine of Option 2 can save 50% of the saw blade cost each year. The specific data are as follows:


In this assumption, R(2-1) is greater than the benchmark investment rate of return, and Option 2 is more feasible.
Assumption 2: Cutting bad materials will not cause cost loss, the labor efficiency is the same, one person operates a sawing machine, but the saw blade loss does not account for a large proportion of the cost. The sawing machine of Option 2 can save 50% of the saw blade cost every year. The specific data are as follows:


In this assumption, the proportion of equipment depreciation in the cost is finally, R(2-1) is far less than the benchmark investment return rate of 13%, and Option 2 is not feasible. In this case, it is more appropriate to use Option 1.


Assumption 3: The saw blade cost accounts for a certain proportion, and cutting bad materials will bring relatively large losses, and the losses are equivalent to the saw blade cost. Then the comparison data of the two options are as follows:


In this assumption, the proportion of equipment depreciation in the cost is finally, R(2-1) will be slightly greater than the benchmark investment return rate of 13%, and Option 2 is more feasible. In this case, it is more appropriate to use Option 2.


Assumption 4: Although cutting the material badly will not cause loss and the saw blade cost is not high, the automation level of Scheme 2 is much higher than that of Scheme 1. If the labor cost of Scheme 1 is three times that of Scheme 2, then the comparison data of the two schemes are as follows:
In this assumption, the proportion of equipment depreciation in the cost is finally, R(2-1) is much greater than the benchmark investment return rate of 13%, and Scheme 2 is more feasible. In this case, it is more appropriate to choose Scheme 2.
Therefore, the selection of sawing machines cannot be generalized, and the proportion of each sub-item cost in the total cost will affect the feasibility of the final plan.

 

Essential information:

Upright Metal Bandsaw

 

Brand: HUOXIAN

Type: Vertical sawing machine

Model: HX-360

 

Product parameters:

 

 

Model

HX-360

Max.Throal Capacity(mm)

350

Max.Thickness Capacity(mm)

240

Table Size(mm)

505×505

Max.Blade length(mm)

2780

Butt-welder Capacity(mm)

3~13

Inclination of table

10°(front & rear)

15°(left & right)

Main Motor4P(hp)

1

or Main Motor8P(hp)

-

Gearbox Power(hp)

1

Blade Speed(APP.M/min)(50Hz)

31/51/76/127

Welding power(kva)

1.2

Butt-welder Capacity(mm)

3~13

Net Weight(kg)

270 Around

Machine Size(L*W*H)(mm)

990×660×1580

 

Features:

 


√ Band saw blade can be sharpened at any time, equipped with a small saw blade welding machine

√ Metal body The cast iron workbench is durable and resistant to deformation.

√ The top saw blade clamping device facilitates the installation of the saw blade.

√ The side chip removal port design saves time and effort and is easy to clean.

√ The cleaning debris brush quickly cleans the debris and protects the saw blade to prevent the debris from hindering the sawing.

√ The top is equipped with a lifting bolt for easy movement.

√ The LED work light illuminates the cutting area and can also work at night

Send Inquiry

You Might Also Like